How To Install A Transition Strip From Laminate To Tile

Installing a T Mold Transition Between Laminate and Ceramic Tile

There are several different types of laminate transitions that you may need when installing laminate flooring. Each i is used specifically for where the laminate flooring ends, such as where the laminate stops at ceramic tile. Other transitions are used where the laminate ends at carpeting, vinyl flooring, a threshold or a footstep down such every bit a sunken living room or stairs.

I volition describe how to install a T mold between laminate floor and ceramic tile on a concrete floor. If you're installing the track on a wood sub flooring, you don't have to worry nearly drilling the concrete. Just utilise forest screws to attach the track. The T mold will snap into the rails after it is installed.  The ceramic tile needs to exist the aforementioned height as the laminate flooring so the transition sits level across the 2 floors. If the laminate or ceramic tile are different heights you may demand to modify the laminate transition.

Stride 1 Cutting the track to the correct length

The first step is to cut the track to the right length. If installing the transition in a doorway cut the track nigh one/two inch short at each stop. The space between the laminate and the ceramic tile should permit the track to have a infinite of ane/4 inch from the laminate and tile.

Footstep 2 Mark where to drill holes in the concrete

Use a modest piece of the T mold equally a guide. Position the sample T mold in the door way where the final position volition be. Hold the track in place where the T mold will be installed. Make marks in the pre-made Lholes of the track using a pencil. Make marks at each finish an two more than between these. Make marks likewise on the ceramic tile to keep rails of where they are.

Pace three Drill the holes in the physical

Use a 1/4 inch masonry drill bit and drill the 4 holes. (In most cases it takes about 4 holes for a typical door way) Drill about 1 1/two inches deep for each hole. Using a hammer drill is much quicker than a normal drill.

Footstep iv Insert wooden dowels in holes and spiral downwardly track

Utilise a 1/4 inch wooden dowel (about .49 cents at Home Depot) Tap the dowel with a hammer into each hole yous drilled, and break off.  Make sure the dowels are flush with the height of the holes. You may take to utilise a chisel and flake any extra woods flat. Position the track in place and use a 1 to one i/ii inch screw to screw the rails down. Don't over tighten the screws.

Step 5 Measure and cut transition

Measure the width and cut the transition, using a miter chop saw if possible. You may have to notch the corners to fit around the door stops in the door jamb. Hold the transition over the rails where information technology volition snap in and make a mark so you lot can cutting the corner. After making the marks on the corners cut them with a jig saw or a small paw saw.

Step 6 Install T mold into track

After cut the transition to fit the door way all you lot need to do is to snap it into the runway. Sometimes when screwing the rail down,  the metal ones tend to pull the sides of the rails inward. Use a spiral driver and spread the sides apart a little so the transition volition snap in the track easier. Outset at one side and piece of work to the other. Make sure the transition is in the track before using a block and hammer to tap information technology down.

Desire to master Microsoft Excel and take your work-from-home job prospects to the adjacent level? Jump-start your career with our Premium A-to-Z Microsoft Excel Training Package from the new Gadget Hacks Shop and get lifetime access to more than xl hours of Basic to Advanced educational activity on functions, formula, tools, and more than.

Purchase Now (97% off) >

Other worthwhile deals to check out:

• 97% off The Ultimate 2022 White Hat Hacker Certification Bundle
• 98% off The 2022 Bookkeeping Mastery Bootcamp Bundle
• 99% off The 2022 All-in-1 Data Scientist Mega Bundle
• 59% off XSplit VCam: Lifetime Subscription (Windows)
• 98% off The 2022 Premium Learn To Code Certification Parcel
• 62% off MindMaster Heed Mapping Software: Perpetual License
• 41% off NetSpot Home Wi-Fi Analyzer: Lifetime Upgrades

Source: https://home-building.wonderhowto.com/how-to/install-t-mold-transition-between-laminate-ceramic-tile-0118343/

Posted by: looneysamet1997.blogspot.com

Share this post